Clarke 250TE Dokumentacja Pobierz pdf (Strona 7)

C) Fire and explosion prevention

Causes of fire and explosion are:

1) combustibles reached by the arc, flame, flying sparks, hot slag or heated

material;

2) misuse of compressed gases and cylinders;

3) short circuits.

BE AWARE THAT flying sparks or falling slag can pass through cracks, along pipes,

through windows or doors, and through wall or floor openings, out of sight of the

goggled operator. Sparks and slag can fly 10M.

To prevent fires and explosion: keep equipment clean and operable, free of oil,

grease, and (in electrical parts) of metallic particles that can cause short circuits.

If combustibles are in area, do NOT weld. Move the work if practicable, to an

area free of combustibles.

Avoid paint spray rooms, dip tanks, storage areas, ventilators. If the work cannot

be moved, move combustibles at least 10M, away out of reach of sparks and

heat; or protect against ignition with suitable and snug fitting, fire- resistant covers

or shields.

Walls, ceilings, and floor near work should be protected by heat resistant covers

or shields. Fire watcher must be standing by with suitable fire extinguishing

equipment during and for some time after welding or cutting if:

a) appreciable combustibles (including building construction) are within 10M.

b) appreciable combustibles are further than 10M, but can be ignited by sparks.

c) openings (concealed or visible) in floors or walls within 10M can expose

combustibles to sparks.

d) combustibles adjacent to walls, ceilings, roofs or metal partitions can be

ignited by radiant or conducted heat.

After work is done, check that area is free of sparks, glowing embers, and flames.

An empty container that held combustibles, or that can produce flammable or

toxic vapours when heated, must never be welded on or cut, unless container

has first been cleaned. This includes.......a thorough steam or caustic cleaning (or

a solvent or water washing, depending on the combustible’s solubility) followed

by purging and inerting with nitrogen or carbon dioxide, and using protective

equipment.

Water filling just below working level may substitute for inerting.

A container with unknown contents should be cleaned (see paragraph above),

do NOT depend on sense of smell or sight to determine if it is safe to weld or cut.

Hollow castings or containers must be vented before welding or cutting - they

can explode.

In explosive atmospheres, never weld or cut where the air may contain flammable

dust, gas, or liquid vapours.

PARTS LIST - MIG 255TE

No. Description Part No. No. Description Part No.

Wire Feed Motor 42V EM22810006

P.C. Board EM22710051

Gas Solenoid Valve EM22900002

Complete Thermostat EM04600113

Rectifier EM22400086

Fan EM22800002

Front Panel EM33710295

Plastic Front EM21690285

Binzel Torch Adaptor EM23005048

On/Off Switch EM22200002

Fuse EM22220002

Fuse Holder EM22220016

Potentiometer Knob EM21690309

Right Side Panel EM33705320

Chain EM10990010

Rear Panel EM33715096

Dividing Panel EM33720099

Mat For Tools EM30905023

Cover Panel EM33705319

Handlebases EM21690235

Handle EM21600030

Torch Conn. Cover EM21690267

Capacitor EM22315003

Input Cable EM20220044

Black Gas Hose EM30900026

Contactor EM22225007

Auxiliary Contacts EM22225018

Choke EM44135073

Auxiliary Transformer EM44140036

Resistance EM22305004

Transformer EM44120084

Complete Fan EM22800021

Wheels Axle EM55200029

Castor EM21625003

Swicth Knob EM21690312

Switch EM22205033

Orange Pilot-lamp EM22610011

Female Plug EM22100002

Rear Wheel EM21625011

Cable Clamp EM21605010

Lower Panel EM33700172

Compl. Spool Holder EM04600001

Left Access Panel EM33705371

Al .wire Feeder EM44410017

Feed Roll 0.6-0.8mm EM33805003

Feed Roll 1.0-1.2mm EM33805005

Feed Roll 0.8-1.0mm nylon EM

33805021

Feed Roll 1.2-1.6mm nylon

EM33805022

Block Roll EM33805007

Slide Clip EM21690226

Earth Clamp EM22110009

Earth Cable EM43210013

Dinse Plug EM22100001

Torch EM23000349

Reducer EM22905017

Face Mask EM21905019

Transparent Glass EM21905020

Dark Glass EM21905024

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Komentarze do niniejszej Instrukcji

Brak uwag

Clarke 250TE Dokumentacja Strona 7

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla System spawalniczy Clarke 250TE