Clarke 250TE Dokumentacja Pobierz pdf (Strona 15)

UNPACKING & PARTS IDENTIFICATION

Unpack and lay out the components, checking against the following list. Any

damage or deficiency should be reported to your CLARKE dealer immediately.

Most of the components are stored within the side compartment. To open the

compartment, put your finger in the hole in the side cover, and pull sharply.

1. Welder complete with Torch and Hose, Earth Cable with Clamp and Power cable.

NOTE:

Migs 151TE and 160EN are NOT provided with 13 Amp plugs. These machines MUST NOT be

connected to a standard 13 Amp domestic supply. See ‘Electrical Connections’ for full details.

2. 2 plastic feet + 2 Wheels w/Axle and 2 Lock washers.(110E, 110EN, - 2 Feet only)

3. 1xHandle Extension and Hand Grip (NOT 110E, 110EN)

4. 1xHandle

5. 1x2-Piece Welding Mask

6. 1xWelding Mask handle, complete with plastic nut and 2xplastic screws.

7. 1xPackage containing 1x Clear Glass and 1x Dark Glass Lens

8. 1xMini Wire Spool, fitted to the Spool Holder

9. 1xplastic bag containing the following:

a1. 110E - 2xSpare Nozzles, 0.6/0.8mm (0.6mm fitted to torch)

a2. 110EN, 130EN, 160EN - 0.6/0.8mm (1.00mm fitted to torch)

a3. 135TE, 151TE - 0.8/1.0mm (0.6mm fitted to torch)

b. 2xScrews for fixing Handle

c. 4xSelf Tapping Screws with flat washers for fixing feet

d. 1xHex Wrench

e. 1xScrew for fixing Handle extension (110E and 110EN)

10. 1xDisposable Gas Cylinder CO

2 .

(NOT EN Models)

11. 1xGas Regulator (NOT EN Models )

12. 1xLarge Worm Drive Clip (NOT EN Models )

ASSEMBLY & INSTALLATION

A. Loose Components

Lie the welder on its side and attach the two feet using the four screws with flat

washers provided. For those models with wheels you have the option of fitting the

two feet, or the wheels as follows: Remove the plug covering the hole for the

axle, insert the axle, then attach the wheels, securing them by pushing the star

locking washers provided, on to the axle, using a piece of tube or an old socket,

ensuring the centre tines face outwards.

Attach the handle to the top of the machine by slotting it into place and securing with

the two screws provided. For those models with a handle extension, simply slide it into the

handle and secure with the screw provided.

The gas bottle is secured to the machine using the large worm drive clip which is threaded

through the opening provided on the rear panel of the machine, (NOT EN Models).

PARTS LIST - MIG 110E

Wire Feeding Motor EM22810001

Complete Thermostat EM04600113

Plastic Handle EM21600021

Torch Grommet on Front Panel EM21690001

Welding Current Switch EM22200006

Potentiometer Knob EM21690017

Yellow Pilot-light Switch EM22200022

Access Panel Hinge EM21690178

Dividing Panel EM33720092

Wire Spool See Accessories

Fixed Spool Holder EM21690011

Spool Holder Retaining Ring EM21690012

Plastic Wire Feeder EM44400001

P.C. Board EM22710043

Cable Clamp EM21605010

Left Access Panel EM33705217

Front Panel EM33710165

Right-side Upper Panel EM33705216

Rear Panel EM33715063

Wire Feed Roll Knurled EM33805001

Front Plastic Frame EM21690175

Side Panel Clip EM21690177

Front Plastic Foot EM21610014

Choke EM44135061

Rectifier EM22400021

Transformer EM44120105

Back Plastic Foot EM21610015

Earthcable EM43210119

Earth Clamp EM22110005

Red Torch compl. EM23000050

Power Cable EM20220068

Back Plastic Frame EM21690176

Spool Holder Handwheel with nut EM21800036

Lower Panel EM33700138

Reducer W/Out Gauge EM22905001

Spare Cartridge C0

See Accessories

Hose Clamp EM22915004

Plastic Mask W/Handle EM21905018

Transparent Glass EM21905020

Dark Glass 82x108 BS Din11 EM21905021

No. Description Part No.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21 22

Komentarze do niniejszej Instrukcji

Brak uwag

Clarke 250TE Dokumentacja Strona 15

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla System spawalniczy Clarke 250TE